Beretta Web - Giulio Sosso - Torino

Beretta 92 History | Beretta 92 DeLuxe | Beretta Billenium | Beretta 90-TWO | Beretta 92 | Beretta 92S | Beretta 92SB
Beretta 93R | Beretta Target | Beretta 92 Combat | Beretta 92 .22LR Kit | Beretta 92A1 | Beretta Vertec Steel | Beretta 92 Gost
Beretta 418 | Beretta 1931-1934 | Beretta 1934 | Beretta 70 series | Beretta 90 | Beretta 950 | Beretta 9000
Beretta 80 Series | Beretta 86 | Beretta 89 | Beretta U22 | Beretta 8000 | Beretta 51 | Beretta Olympic
Beretta CX4 | Beretta PX4 | Beretta PX4 SC | Beretta RX4 | Beretta PX4 .45ACP SD |
Beretta 412 series | Beretta A300 | Beretta 1200 | Beretta Pump Guns | Beretta SO series | Beretta SO5 | Beretta UGB25
Beretta 91 | Beretta MAB series | Beretta PM12 S2 |

Beretta Web - Giulio Sosso Pistol 9mm

Unofficial Beretta Site

...
The real innovations are always refused and after copied!

Personally, I believe that for his time (the 30s), Eng. Giulio Sosso was an incredible innovator, many of his concepts: Aluminum frame, Locking by means of an oscillating block, Double action, Automatic firing pin safety, Double-stack magazine, were copied, modified and introduced on modern pistols that came on the market several years later.

A special thanks to Dr. Enrico Appiano who made the published documentation available to me.

Two pistols are exhibited in the Beretta Arms Factory museum, probably prototypes under evaluation of Patents.

Below the original Italian writing you can read the translation made by Chat GPT.

NUOVI principi COSTRUTTIVI DELLE ARMI PORTATILI Secondo i brevetti: IULIO SOSSO - TORINO sono fondamentalmente basati:

1) su uno speciale sistema di alimentazione a mezzo di nastro continuo porta-cartucce, girevole fra due perni incorporati nel caricatore, ruotante di un passo ad ogni escursione dell'otturatore (alimentazione comandata);

2) sull'adozione della canna rinculante con nuovo, speciale sistema di bloccaggio di quest'ultima con l'otturatore, senza supplementare ausilio di molle;

3) su una sicurezza speciale sul percussore in modo che questo non possa diventare attivo, se non nel preciso momento del tiro; ,

4) sul fatto che le tre uniche molle esistenti nel sistema sono in perenne stato di riposo e non entrano in tensione che al momento del tiro. Una pratica applicazione di questi principi basilari, da semiautomatica cui scaturisce tutta una serie di ragguardevoli vantaggi, è stata realizzata nella pistola automatica che si presenta in questo opuscolo. E' in corso la realizzazione pratica, basata sugli identici principi, di un moschetto a trenta colpi, suscettibile di sparare in modalità semiautomatica oppure a raffiche controllate di tre colpi ciascuna. Farà seguito la realizzazione della mitragliatrice leggera e pesante.

  IULIO SOSSO - TORINO  

La pistola automatica Sosso è del tipo a canna rinculante (corto-rinculo). Questa caratteristica presenta, come è noto, numerosi vantaggi, che si possono riassumere come segue: 1) Sfruttamento dell'espansione dei gas assai maggiore di quello ottenibile con le pistole a canna fissa, con conseguente maggior potenza balistica (alta velocita iniziale), dovuta alla forte pressione che avviene per il continuo e progressivo forzamento del proiettile per tutta la lunghezza dell'anima della canna. 2) Arretramento dell'otturatore assai meno violento, avendo esso inizio quando il proiettile è già uscito dalla canna e cioè quando la pressione dal massimo è scesa a limiti sopportabili, ottenendo cosi maggior dolcezza di funzionamento, particolarmente nell'estrazione del bossolo. 3) Immobilizzo dell'arma in caso di occlusione della canna (per presenza di proiettile in essa arrestatosi per deficienza di carica) e conseguente eliminazione di ogni pericolo per lo sparatore. Nelle pistole a canna fissa ed in genere in tutte le armi non dotate di bloccaggio, in simile caso, si verifica: - rinculo di otturatore; - messa in canna di una seconda cartuccia che può esplodere, ad accensione avvenuta, fuori della camera di scoppio; - conseguente pericolo di chi impugna l'arma. 4) Massima stabilità e perfezione di tiro, in quanto il mivimento rinculante inizia il moto retrogrado quando il proiettile e già uscito di canna e non trasmette, pertanto, al tiratore, quei contraccolpi bruschi, che si verificano, invece, nel tiro con armi a canna fissa, in cui il moto retrogrado dell'otturatore inizia contemporaneamente al moto in avanti del proiettile.

 

IULIO SOSSO - TORINO 1

 

Si presenta, qui, spontanea la domanda: Perchè la maggior parte dei costruttori di armi automatiche, ed in particolare di pistole, preferisce adottare la canna fissa, invece della rinculante? La risposta è semplice: Perchè la disposizione a canna rinculante è necessario adottare il sistema di bloccaggio della canna con l'otturatore, il che porta: a) all' itroduzione di un maggior numero di pezzi e ad una maggiore lavorazione; b) ad una sensibile complicazione nella struttura generale dell'arma; c) ad un maggior peso. Verificasi, in conseguenza di tutto ciò, un maggior costo di fabbricazione ed è per l'appunto in considerazione di quanto sopra che le Fabbriche d'Armi non adottano il sistema della canna rinculante, ricorrendo, invece, al più economico sistema della canna fissa. Ora, con il sistema di bloccaggio (Sosso ), sistema positivo, cioè senza impiego di molle, i tre accennati inconvenienti sono stati integralmente eliminati, ottenendosi tutto il complesso di vantaggi conferiti all' arma dalla canna rinculante, senza complicare l'arma stessa, senza aumentare il peso e senza incidere sul costo di fabbricazione. Ecco come e stato risolto il problema, secondo il sistema ( Sosso ): Il bloccaggio della canna avviene per mezzo di un puntone articolato alla canna stessa che, in posizione normale, è frapposto fra la canna e l'otturatore e, in posizione di rinculo, dopo breve tratto, è abbandonato dall'otturatore e resta frapposto fra la canna ed il castello. Il puntone posteriormente articolato, senza un perno materiale, ad una appendice della canna. L'estremità anteriore, in posizione normale, punta contro un arresto dell'otturatore.

 

IULIO SOSSO - TORINO 3

Quando questo rincula, dopo breve tratto, detta estremità del puntone viene a trovarsi in corrispondenza di un vano del castello in cui viene guidata da un piano inclinato, abbandonando I ‘otturatore, il quale, strisciandovi sopra, mantiene il puntone nel vano 10. Nello stesso tempo che il puntone prende posto nel vano del castello, la canna rinculante con l'otturatore trova un arresto contro il quale resta bloccata dal puntone. Nella corsa di ritorno, verso la fine, l'otturatore libera il puntone e lo spinge, assieme alla canna, in posizione normale, per opera della molla di ricupero, senza necessità di una molla supplementare.

Gli schemi 1, 2, 3, danno un'idea chiara di quanto sopra espresso: La fig. 1 rappresenta la pistola automatica ( Sosso ) a canna rinculante, in posizione normale e parzialmente sezionata, pronta per il tiro. La fig. 2 rappresenta la stessa arma a rinculo totale di canna e parziale di otturatore, con bloccaggio della canna con il castello. La fig. 3 rappresenta l'arma a rinculo totale dell'otturatore. Come chiaramente risulta dagli schemi sopracitati, l'arma presenta il castello, che si estende molto avanti.

n esso scorrevole fra guide, come d'ordinario, l'otturatore 2, di cui e visibile pure la coda zigrinata 2 a, che avvolge la canna 3 e forma astuccio per la molla di ricupero 4, il quale ha il suo appoggio posteriore sul fondo della ghiera 5, che preme contro opportuni arresti del castello. La canna e scorrevole entro questa ghiera nei limiti consentiti dagli arresti 3a e 3b della sua estremità posteriore e del ritegno 6 portato dal castello (sfilabile per lo smontaggio dell'arma).

L'otturatore e la canna sono collegati, nel movimento di rinculo e di ritorno, per mezzo del puntone 7, di cui la estremià posteriore 7a trova posto, a guisa di articolazione, in un incavo della canna presso l'appendice 3 a. La estremità anteriore 7b del puntone, nella posizione normale (fig. 1, arma pronta per il tiro), punta contro un arresto 2b dell'otturatore, mentre in posizione di rinculo trova posto nell'incavo 1a del castello in cui viene guidata attraverso un piano inclinato per l'impegno del suo vano a V 7c con il cuneo 1c del castello. Quando parte il colpo, la canna rincula, spingendo indietro l'otturatore insieme con il puntone 7, fino a che (fig. 2) il vano 7 c del puntone si impegna con il cuneo 1c del castello, l'estremità 7 b del puntone scivola nel vano 1a e l'appendice 3. della canna urta il ritegno 6. L'otturatore per inerzia prosegue la sua corsa indietro, strisciando col suo arresto 1b sul puntone 7 (fig. 3) e mantenendone, cosi, I'estremità 7b nell'incavo 1a: perciò la canna resta bloccata nella posizione di rinculo per tutto il tempo che l'otturatore impiega per giungere a fine corsa e tornare alla posizione di fig. 2. Solo allora I'estremità 7b del puntone sarà libera di risalire il piano inclinato sotto la spinta della canna, a sua volta spinta dall'otturatore sotto l'azione della molla di ricupero. L'arma si trova cosi pronta per la partenza di un nuovo ciclo di sparo (fig. I). il ritorno della canna non è subordinato all'azione di una speciale molla ed è in ogni caso sincrono a quello dell' otturatore, come pure il rinculo, grazie alla rigidità del collegamento per mezzo del puntone.

MECCANISMO DI SCATTO. Il meccanismo di scatto comprende una sola molla, robustissima, elicoidale, che funge sia da molla per il ritorno del grilletto, sia da molla del dente di scatto (fig. 5).

MECCANISMO DI SPARO. La pistola ( Sosso ) e’ del tipo a cane esterno, che e’di facile manovra e controllo. Il cane può essere armato sia agendo direttamente su di esso col pollice, sia premendo il grilletto con l'indice, come in un comune revolver (richiamo automatico). Ciò e’ di notevole importanza pratica, in quanto che, in caso di mancato colpo, si può riarmare il cane semplicemente ritirando il grilletto e senza dover estrarre la cartuccia non sparata, dato che, come succede spesso, la causa del mancato colpo può essere accidentale e indipendente dalla cartuccia. Si ha anche il vantaggio di non distogliere l'arma dalla mira.

MECCANISMO DI SICUREZZA (fig. I, 2, 3, 4.- pag. I4). La pistola ( Sosso ) e’ provista di una sicura automatica che viene liberata solamente quando si preme il grilletto. Tale sicura blocca il percussore. Anche se il cane fosse sollevato e dovesse scattare accidentalmente, esso non potrebbe provocare la partenza del colpo, se il grilletto non e’ premuto, per cui I ‘arma può essere portata senza pericolo anche con il cane armato

 

 

 

 

 

 

 

 

 

CARICATORE (vedi fig. 4). La pistola automatica ( Sosso ) è provvista di un caricatore di nuovo tipo il quale consente un numero di colpi all'incirca triplo di quello contenuto nei caricatori ordinari a molla. Nel caricatore ( Sosso ) le cartucce sono portate da un nastro continuo, girevole fra due perni incorporati con il magazzino, amovibile nel modo solito. L'avanzamento del nastro, ad ogni colpo, è provocato dal rinculo dell'otturatore.

Nel caricatore è esclusa qualsiasi molla e la scorrevolezza della cartuccia alla messa in canna è uguale dal primo all'ultimo colpo ed è eliminato qualsiasi pericolo di inceppamento, che, come è noto, nei caricatori ordinari è dovuto: a) all'eccessiva spinta esercitata sulle cartucce, specialmente ai primi colpi, quando la molla è compressa al massimo grado; b) allo snervamento, a lungo andare, della molla stessa, che non riesce più a spingere, con la dovuta energia, le ultime cartucce al punto in cui debbono venire investite dall'otturatore; c) all'allargamento dei labbri del caricatore con conseguente sbandamento delle cartucce rispetto all'asse della canna; d) alla rottura della molla per eccessiva compressione.

Nel caricatore (Sosso ), le cartucce si immettono, dalla prima fino all'ultima, negli appositi alveoli, con estrema facilità e senza esercitare alcuno sforzo, mentre invece, negli ordinari caricatori a molla, notevole è la pressione che si deve esercitare per farvi entrare le ultime cartucce, dovendo vincere la reazione della molla, già fortemente compressa. A notarsi poi che se, in tale operazione, non si procede con cautela, si corre anche il rischio di slabbrare il caricatore, dando così luogo alla possibilità di inceppamento dell'arma.

.

 

 

 

 

 

RIASSUNTO DEI PREGI DELLA PISTOLA AUTOMATICA "SOSSO go. I) Eliminazione integrale degli inceppamenti che molte volte si producono nell'uso delle pistole ordinarie e che sono dovuti all'imperfetto sistema di alimentazione con i comuni caricatori a molla. 2) Disponibilità di colpi all'incirca tripla di quella delle comuni pistole automatiche. 3) Notevole celerità di tiro consentita dall'alimentazione comandata, in sincronia con l'escursione dell'otturatore. 4) Potenza balistica elevatissima, a causa della forte strozzatura di canna (forzamento continuo e progressivo del proiettile per tutta la lunghezza dell'anima) e della minima dispersione di gas dovuta al sistema di chiusura stabile. 5) Pezzi costitutivi dell'arma robustissimi e di facile lavorazione. 6) Facilità e rapidità estrema di montaggio e di smontaggio, non essendovi nè viti nè coppiglie fisse al castello. 7) Stabilità perfetta di tiro. 8) Richiamo automatico del cane e quindi possibilità di ripetere la percussione, senza distogliere l'arma dalla mira. 9) Sicurezza agente sul percussore, per cui il colpo non esplode, anche se l'arma cade o urta violentemente contro qualche corpo solido. 10) In tutta I'arma non vi sono che tre molle, robustissime, in costante stato di riposo, che entrano in tensione solo al momento del tiro. Sono basati sullo stesso principio di funzionamento i moschetti, fucili, mitragliatrici leggere e pesanti, sistema "GIULIO SOSSO"

 

   

MANUTENZIONE DELL'ARMA (pag. I5, I6). Lo smontaggio è di una semplicità senza confronti: esso avviene senza l'uso di alcun utensile. Viene dapprima sfilato il caricatore 8, dopo aver spostata da sinistra a destra la leva 9, che serve da fermo. Tenendo l'arma nel palmo della mano, la stessa leva 9 viene premuta verso linterno (da destra verso sinistra) per tutta la sua corsa, con questo movimento si sgancia la guancia-coperchio 10, asportandola dal castello 1. Si ha cosi sott'occhio ogni meccanismo. Si sfila quindi la ghiera (guida canna) 5; si alza il cane 1, si tira indietro I'otturatore 2, che si alza fuori dalle guide e si spinge innanzi, sfilandolo anteriormente; si toglie la molla di ricupero 4 e relativa guida I2; si abbassa il cane, si toglie l'arpione 13, sollevandolo verso l' alto ed asportandolo; si toglie la biella 14 e quindi il grilletto 15 con incorporata molla 16 e comando 17 della sicura, nonchè il relativo congegno di scatto 18; si toglie il fermo canna 19 e poi la canna 3, spingendola indietro fino a fuori guida; quindi il puntone 7, la coppiglia 20 e si sfila l'arresto 2I, che tiene l'arma in posizione aperta quando l'otturatore è a fine corsa. Quindi si sfila il perno 22, togliendo il complesso: cane 11, molla 23 e comando elastico arpione 24. Si asporta il pernetto 25 per il fermo del caricatore e L'asticciola 26 di bloccaggio della guancia 10. Nell'otturatore 2: tolta la coppiglia 27 si asporta l'estrattore 28 e quindi automaticamente si sfila il percussore 29 e il congegno di sicura 30. Nell'arma, le tre sole molle esistenti (4, 16, 23) sono costantemente in stato di riposo, entrando esse in tensione solo durante il tiro.

     

Caratteristiche generali

Calibro: 9 mm Glisenti
Sistema di Chiusura: Stabile con blocco di chusura
Cane: Esterno
Lunghezza Totale: 170 mm
Altezza totale: 140 mm
Spessore
: 33 mm
Lunghezza canna: 120 mm
Peso totale con caricatore vuoto: 714 gr
Peso del caricatore vuoto: 150 gr
Azione: Singola e Doppia azione
Sicura:
Automatica al percussore
Alimentazione : Caricatore amovibile
Capacità Caricatore: 19 colpi
Sviluppo: 1930
Anno inizio Produzione: 1940 (?)
Quantità Prodotte: Sconusciuta

   

 

 

Giulio Sosso – Turin

NEW DESIGN PRINCIPLES FOR SMALL ARMS

According to the patents of Giulio Sosso – Turin, the new design principles for small arms are fundamentally based on the following features:

  1. A special feeding system using a continuous cartridge-carrying belt rotating around two pins incorporated into the magazine, advancing one increment with each movement of the slide (mechanically controlled feeding).

  2. The adoption of a recoil-operated barrel with a new, special locking system connecting the barrel to the slide, without the additional use of springs.

  3. A special firing-pin safety mechanism that prevents the firing pin from becoming active except at the precise moment the shot is fired.

  4. The fact that the only three springs in the entire mechanism remain permanently at rest and are placed under tension only when the weapon is fired.

A practical application of these fundamental principles, from which a whole series of significant advantages is derived, has been incorporated into the automatic pistol presented in this brochure.

A 30-round carbine based on the same principles is also under development. It will be capable of firing in semiautomatic mode or in controlled three-round bursts. Development of light and heavy machine guns will follow.

THE SOSSO AUTOMATIC PISTOL

The Sosso automatic pistol is a recoil-operated, short-recoil design.

As is well known, this configuration offers numerous advantages, which can be summarized as follows:

  1. More efficient use of expanding gases. This is considerably greater than that achieved with fixed-barrel pistols, resulting in increased ballistic performance and higher muzzle velocity. This is due to the substantial pressure generated by the continuous and progressive engagement of the bullet with the rifling along the entire length of the barrel bore.

  2. Less violent rearward movement of the slide. Its rearward movement begins only after the bullet has left the barrel, when the pressure has dropped from its maximum level to within acceptable limits. This results in smoother operation, particularly during cartridge-case extraction.

  3. The weapon remains immobilized if the barrel becomes obstructed. This may occur when a bullet remains lodged inside the barrel because of an insufficient powder charge. The system therefore eliminates the resulting danger to the shooter.

In fixed-barrel pistols and, generally, in all firearms without a locking mechanism, the following may occur under similar circumstances:

  • The slide moves rearward.

  • A second cartridge is chambered and may fire outside the chamber.

  • The person holding the weapon is consequently exposed to danger.

  1. Maximum stability and shooting accuracy. The recoil movement begins only after the bullet has left the barrel. Consequently, the shooter is not subjected to the sharp jolts that occur when firing fixed-barrel weapons, in which the rearward movement of the slide begins simultaneously with the forward movement of the bullet.

This naturally raises the following question: Why do most manufacturers of automatic firearms, particularly pistols, prefer fixed barrels rather than recoil-operated barrels?

The answer is simple:

With a recoil-operated barrel, it is necessary to employ a locking system between the barrel and the slide, which results in:

a) The introduction of a greater number of components and additional machining operations;

b) A considerably more complicated overall design of the weapon;

c) Increased weight.

As a consequence, manufacturing costs are higher. It is precisely because of these considerations that firearms manufacturers generally avoid the recoil-operated barrel system and instead adopt the less expensive fixed-barrel arrangement.

With the Sosso locking system, however, which provides positive mechanical locking without the use of springs, all three of the above-mentioned disadvantages have been completely eliminated.

The full range of advantages offered by a recoil-operated barrel is thus achieved without complicating the weapon, increasing its weight, or adding to manufacturing costs.

THE SOSSO LOCKING SYSTEM

Here is how the problem has been solved using the Sosso system:

The barrel is locked by means of a link connected to the barrel itself. In the normal position, this link is located between the barrel and the slide. During recoil, after a short initial movement, the slide disengages from the link, which then remains positioned between the barrel and the frame.

The rear end of the link is articulated, without a physical pivot pin, to a projection on the barrel. In the normal position, its front end rests against a stop on the slide.

As the slide moves rearward, after a short distance, the front end of the link reaches a recess in the frame, where it is guided by an inclined surface. This disengages it from the slide, which then slides over the link and keeps it seated in recess 1a.

At the same time that the link engages in the frame recess, the recoiling barrel and slide assembly reaches a stop against which the barrel is held by the link.

During the return stroke, near the end of its movement, the slide releases the link and pushes it, together with the barrel, back into its normal position under the action of the recoil spring, without requiring an additional spring.

Diagrams 1, 2, and 3 clearly illustrate the operation described above:

  • Figure 1 shows the Sosso automatic pistol with its recoil-operated barrel in the normal position, partially sectioned and ready to fire.

  • Figure 2 shows the same weapon with the barrel at the end of its recoil travel and the slide partially retracted, with the barrel locked to the frame.

  • Figure 3 shows the weapon with the slide at the end of its rearward travel.

As is clearly shown in the above diagrams, the weapon features a frame that extends considerably forward.

The slide (2) runs along guides in the frame in the conventional manner. Its knurled rear extension (2a) surrounds the barrel (3) and forms a housing for the recoil spring (4). The rear end of this spring rests against the bottom of the retaining collar (5), which bears against suitable stops in the frame.

The barrel slides inside this collar within the limits established by the stops (3a and 3b) at its rear end and by the retaining catch (6) mounted on the frame. This catch can be removed when disassembling the weapon.

During both the recoil and return movements, the slide and barrel are connected by means of the link (7). Its rear end (7a) is seated, in the manner of an articulated joint, in a recess in the barrel near projection (3a).

In the normal position (Figure 1, weapon ready to fire), the front end of the link (7b) rests against a stop (2b) on the slide. In the recoil position, it engages in recess (1a) in the frame, where it is guided by an inclined surface as its V-shaped opening (7c) engages with the frame wedge (1c).

When the shot is fired, the barrel recoils, driving the slide rearward together with link (7), until the link's V-shaped opening (7c) engages with the frame wedge (1c), the front end (7b) of the link slides into recess (1a), and the barrel projection (3) strikes the retaining catch (6).

The slide continues its rearward movement by inertia, with its stop (1b) sliding over link (7) (Figure 3), thereby keeping the front end (7b) of the link inside recess (1a).

The barrel consequently remains locked in its recoil position throughout the time required for the slide to reach the end of its travel and return to the position shown in Figure 2.

Only at that point is the front end (7b) of the link free to move back up the inclined surface under the force exerted by the barrel, which is itself pushed forward by the slide under the action of the recoil spring.

The weapon is then ready to begin a new firing cycle (Figure 1).

The return movement of the barrel does not depend on a separate spring and is always synchronized with that of the slide, just as the recoil movement is, thanks to the rigid connection provided by the link.

MAGAZINE (SEE FIGURE 4)

The Sosso automatic pistol is equipped with a new type of magazine that provides approximately three times the capacity of conventional spring-operated magazines.

In the Sosso magazine, the cartridges are carried by a continuous belt rotating around two pins incorporated into the magazine assembly, which is removable in the usual manner.

The belt advances automatically with each shot, driven by the rearward movement of the slide.

No springs whatsoever are used in the magazine. Cartridge feeding into the chamber is equally smooth from the first round to the last, eliminating the possibility of the feeding malfunctions commonly associated with conventional magazines.

As is well known, such malfunctions in ordinary magazines may be caused by:

a) Excessive pressure exerted on the cartridges, particularly the first rounds, when the spring is compressed to its maximum extent;

b) Fatigue of the spring over time, causing it to lose its ability to push the last cartridges into the correct position with sufficient force for engagement by the slide;

c) Expansion of the magazine feed lips, causing the cartridges to become misaligned with the barrel axis;

d) Spring breakage due to excessive compression.

In the Sosso magazine, cartridges can be inserted into their respective compartments with extreme ease, from the first to the last, without requiring any significant effort.

By contrast, with conventional spring-operated magazines, considerable pressure must be applied to insert the last cartridges because of the resistance of the already heavily compressed spring.

It should also be noted that, if this operation is not carried out carefully, there is a risk of spreading the magazine feed lips, potentially causing the weapon to malfunction.

TRIGGER MECHANISM

The trigger mechanism contains only one extremely robust coil spring, which serves both as the trigger-return spring and as the sear spring (Figure 5).

FIRING MECHANISM

The Sosso pistol features an external hammer, which is easy to operate and control.

The hammer can be cocked either directly with the thumb or by pulling the trigger with the index finger, as with a conventional revolver (double-action operation).

This is of considerable practical importance because, in the event of a misfire, the hammer can be cocked again simply by releasing and pulling the trigger, without having to remove the unfired cartridge.

As often happens, the cause of a misfire may be accidental and unrelated to the cartridge itself.

Another advantage is that the shooter does not have to take the weapon off target.

SAFETY MECHANISM (FIGURES 1, 2, 3, AND 4 – PAGE 14)

The Sosso pistol is equipped with an automatic safety that is released only when the trigger is pulled.

This safety mechanism blocks the firing pin.

Even if the hammer were cocked and accidentally released, it could not cause the weapon to fire unless the trigger were being pulled.

The weapon can therefore be carried safely even with the hammer cocked.

MAINTENANCE AND DISASSEMBLY (PAGES 15–16)

Disassembly is exceptionally simple and requires no tools whatsoever.

First, remove the magazine (8), after moving the retaining lever (9) from left to right.

While holding the weapon in the palm of the hand, press the same lever (9) inward (from right to left) through its entire travel. This movement releases the side cover panel (10), allowing it to be removed from the frame (1).

All the internal mechanisms are then accessible for inspection.

Next, remove the barrel collar (barrel guide) (5); cock the hammer (11); pull the slide (2) rearward until it lifts out of its guides, then move it forward and remove it from the front.

Remove the recoil spring (4) and its guide (12).

Lower the hammer and remove the sear (13) by lifting it upward and taking it out.

Remove the connecting link (14), followed by the trigger (15), which incorporates spring (16) and the safety control (17), together with the associated trigger mechanism (18).

Remove the barrel retainer (19), then push the barrel (3) rearward until it clears its guides and can be removed.

Next, remove link (7), the retaining pin (20), and the stop (21), which holds the weapon in the open position when the slide reaches the end of its travel.

Then remove pin (22), taking out the complete assembly consisting of the hammer (11), spring (23), and elastic sear control (24).

Remove the small pin (25) that retains the magazine and the small locking rod (26) that secures the side cover (10).

In the slide (2), after removing retaining pin (27), remove the extractor (28). The firing pin (29) and safety mechanism (30) can then be withdrawn automatically.

The weapon contains only three springs (4, 16, and 23). These remain permanently at rest and are placed under tension only when the weapon is fired.

PISTOL DIMENSIONS AND WEIGHT (9 mm CALIBER)

Specification Measurement
Overall length 170 mm
Barrel length 120 mm
Grip thickness 33 mm
Frame weight, lightweight material 265 g
Accessories weight 450 g
Total unloaded weight 715 g
Empty magazine weight 150 g
Weight of 19 cartridges 228 g
Total weight, fully loaded with 19 cartridges 1,093 g

SUMMARY OF THE ADVANTAGES OF THE SOSSO AUTOMATIC PISTOL

  1. Complete elimination of the feeding malfunctions frequently encountered with conventional pistols, which are caused by the imperfect feeding system of ordinary spring-operated magazines.

  2. Approximately three times the ammunition capacity of conventional automatic pistols.

  3. A remarkably high rate of fire, made possible by mechanically controlled feeding synchronized with the movement of the slide.

  4. Extremely high ballistic performance, resulting from the strong barrel constriction (continuous and progressive engagement of the bullet with the rifling along the entire length of the bore) and minimal gas loss due to the stable locking system.

  5. Extremely robust component parts that are easy to manufacture.

  6. Exceptional ease and speed of assembly and disassembly, with no screws or retaining pins permanently attached to the frame.

  7. Outstanding shooting stability.

  8. Automatic hammer recocking, allowing the firing pin to strike again without the shooter having to take the weapon off target.

  9. A firing-pin safety mechanism that prevents the weapon from discharging even if it is dropped or strikes a hard object with considerable force.

  10. The entire weapon contains only three extremely robust springs, which remain permanently at rest and are placed under tension only at the moment of firing.

Carbines, rifles, and light and heavy machine guns based on the same operating principle are also part of the Giulio Sosso system.

Stat | Site Map | Links | Contact Us | ©2026 BERETTAWEB.com